Only signed in users will see discount codes and have complete access to product lines, datasheets and pricelists
CAPLINQ offers a range of LINQSTAT-branded electrically conductive and antistatic plastic film. Antistatic plastics typically have a surface resistance less than 100,000 ohms-per-square. Electrically conductive plastics start with a surface resistivity of less than 10,000 ohm-per-square and can go as low as 10 ohms-per-square.
LINQSTAT™ VCF, MVCF- and XVCF-Series electrically conductive plastic sheeting is a black, carbon-filled, volume-conductive polyethylene film designed to provide both physical and static protection in numerous semiconductor, electronics, and Smartcard applications. The different grade of materials allows users to cover a wide range of possible applications.
The film and its conductivity are unaffected by humidity and age. The film is heat-sealable, flexible and offers exceptional abrasion resistance. The film gives good thermal stability and has outstanding chemical resistance. LINQSTAT has a standard thickness range from 65-200 micron (0.0025 inch to 0.008 inch) and roll lengths and widths vary depending on application and requirement.
One question we get very, very often is if we can offer products with a specific resistivity, conductivity, thickness or width. The answer to this question is yes and no. Yes, we can make custom conductivities between 200 ohms/sq and 200,000 ohms/sq. Thicknesses from 50um to 200um and widths up to 510mm. However, due to the manufacturing process, this typically requires a minimum order of approximately 300 kg which equates to roughly 100 rolls of 91cm length.
Due to the overwhelming popularity of these requests, we have adopted a policy whereby we request that customers wishing a specific conductivity, thickness or width to pay $1500 upfront towards the cost of the rolls to make a custom product not currently available online. All other customers are asked to order one of our currently available products.
Another question we get very often (I guess that's why they are FAQs) is that customers are not sure if the product will work for their applications and the request to get a "Sample Kit". By popular demand, we have created sample kits of both electrically conductive and anti-static plastic films. Though these might be more expensive than the rolls themselves, it allows users to test a range of materials to see if it meets their specific requirements. Click this link to be take to our You will find a link to this below.Linqstat Sample Kits. Sorry, there are no substitutions.
We try to put all the information we currently have available online. If the information you are looking for is not in the Product Selector Guide, on the Product Page, in Technical Data Sheet, in Learn More section or in a blog article, you can assume that it is not yet available. We can and do want to provide more data, but we need to charge laboratory time for this work. Our lab rates are $175/hr.
3M manufacture a family of products made of black, volume conductive plastics under the tradename Velostat®. Though the tradename Velostat belongs to 3M, the product itself is not under patent. This means that other companies are allowed to manufacture similar products with no conflict with 3M. Please click here to read the article on generic vs brand-name products.
Similar to Velostat, CAPLINQ offers a line of volume-conductive plastics under its LINQSTAT brand name. LINQSTAT VCF is a black, carbon-loaded, electrically-conductive plastic. Unlike Velostat, CAPLINQ's product line is far more extensive, offering far more grades than 3M with different conductivity levels to give a better balance of price vs performance for your specific application. Compare the technical properties of your Velostat® Film to those found in the table below and on CAPLINQ's respective LINQSTAT Technical Datasheets.
We don't provide electrically conductive films with any adhesives at all. Films are all "as is" with no backings or coatings. On the same note we do not sell corona, flame or plasma pretreated rolls with enhanced surface energy.
We don't provide Polyethylene compatible adhesives. PE surface tension is very low so it is quite challenging to reach proper adhesion. Heat sealing is usually the best option but you can always consider corona, plasma or flame treating the films to achieve proper bonding with more standardized acrylic adhesives and processes.
We can assure you that the surface resistivity will always be lower than the stated property. We have various films ranging from 250 up to 200000 ohms/sq so pick the one closer to your needs. Linqstat is not meant for very narrow requirements.
The main difference between these product lines is the surface resistivity. XVCF are our most carbon loaded films and can go as low as 250 ohms/sq. We do have experimental options that can go as low as 50 ohms/sq but due to the complete change to the polymer structure the cost difference is so high (almost tenfold) that doesn't justify mass production. In need of something like that? Contact us.
Few plastic resins are inherently conductive, so it is necessary to modify the plastic in one way or another to make the plastics conductive. There are several ways to make a plastic conductive, among them the most important are as follows: