• x

LOCTITE HHD 3607BK

Harmonization Code : 3907.30.00.90 |   Polyacetals, other polyethers and epoxide resins, in primary forms; polycarbonates, alkyd resins, polyallyl esters and other polyesters, in primary forms : Epoxide resins : Other
Main features
  • Jettable PUR
  • Moisture cure
  • High adhesion strength

Product Description

LOCTITE HHD 3607BK is a reactive hot-melt adhesive based on reactive polyurethane prepolymers. This moisture curable product is formulated with a viscosity suitable for robotic jetting applications along with a suitable open time for automatic assembly line processing.

LOCTITE HHD 3607BK exhibits good initial strength that is realised immediately after the materiaL solidifies in the bondline. LOCTITE HHD 3607BK material exhibits superior toughness, works great with glass surfaces and will not remelt when fully cured.

Product Family
HHD3607BK  
30cc Syringe

Catalog Product

Unlike other products we offer, the products listed on this page cannot currently be ordered directly from the website.
Not Available Shipping in 8 - 12 weeks

Technical Specifications

Mechanical Properties
Hardness
Hardness
Hardness is a dimensionless quantity. There is no direct relationship between measurements in one scale and their equivalent in another scale or another hardness test.
Durometer (Shore D) 75
Elongation
Elongation
Elongation is the process of lengthening something.

It is a percentage that measures the initial, unstressed, length compared to the length of the material right before it breaks.

It is commonly referred to as Ultimate Elongation or Tensile Elongation at break.
880 %
Viscosity
Viscosity
Viscosity is a measurement of a fluid’s resistance to flow.

Viscosity is commonly measured in centiPoise (cP). One cP is defined as
the viscosity of water and all other viscosities are derived from this base. MPa is another common unit with a 1:1 conversion to cP.

A product like honey would have a much higher viscosity -around 10,000 cPs-
compared to water. As a result, honey would flow much slower out of a tipped glass than
water would.

The viscosity of a material can be decreased with an increase in temperature in
order to better suit an application
Viscosity 6,500 mPa.s

Additional Information

How can I clean my equipment after using HHD 3607BK?

For HHD 3607BK we would recommend TECHNOMELT PUR CLEANER 2 or any equivalent cleaning agent.
Typically we suggest to:

  1. Run the equipment with at least ~5ml of this PUR CLEANER 2 out of the bleed port on the side,
  2. Close the bleed port 
  3. Run another 1-2ml out of the needle.

This way there’s no need to fully breakdown the pump if running the same product (like HHD 3607BK) all the time as long as you can make sure that about 6-7ml total bleed occurs.
This is generally a better option than IPA which is mainly used for cleaning equipment in use with varying adhesives but please note that this TECHNOMELT PUR CLEANER 2 is only available in 20kg package which won’t be practical for lab work.

You can also take a look at LOCTITE MSC 01, a softer IPA solder paste cleaner that could be use as an alternative or at LOCTITE SF 7360 which comes in handy 500ml bottles and it is a multi-purpose cleaner for epoxy adhesive residues and conductive/non conductive adhesives.

While we cannot guarantee those 2 will work we will be happy to support you with any questions that might occur.

PUR cleaners

PUR Cleaners are higher viscosity PUR based liquids which do not cure and fill the equipment when not in use. Reactive hot melts like 3607BK will cure in the system when not in use, so  they have to be purged out when you stop.

It is likely that any PUR cleaner without cure can do this as long as you purge the cleaner, e.g. replace the cleaner with fresh 3607BK when you start dispensing again.