• x

TGP 3000 | Thermal Gap Pad

Harmonization Code : 3824.99.96.99 |   Prepared binders for foundry moulds or cores; chemical products and preparations of the chemical or allied industries (including those consisting of mixtures of natural products), not elsewhere specified or included : Other : Other: Other
TGP3000 | Thermal Gap Pad
TGP3000 | Thermal Gap Pad
TGP3000 | Thermal Gap Pad
Main features
  • 0.65 Thermal Impedance
  • 3.0 Thermal Conductivity
  • Low pressure versus deflection

Product Description

Honeywell's TGP3000 has a hardness of about 40 on shore00 that provides low pressure versus deflection. The full compression vs Deflection chart can be seen in the Additional information section. It is naturally tacky, and requires no additional adhesive which could inhibit thermal performance. 

Honeywell's TGP3000 Thermal Gap Pads (TGP) provide high thermal performance with ease of use across a multitude of applications. Their ultra-high compressibility enables low stress and excellent conformity to mating surfaces. They are designed to minimize thermal resistance at interfaces, and maintain excellent performance through reliability testing. The entire series can be die cut according to your application needs.

Products are available in a thickness range from 0.5mm to 5.0mm.

 

 

Product Family
TGP3000  
457 x 457 x 1.0mm Sheet 457 x 457 x 1.5mm Sheet 457 x 457 x 2mm Sheet 457 x 457 x 3mm Sheet 457 x 457 x 2.5mm Sheet

Catalog Product

Unlike other products we offer, the products listed on this page cannot currently be ordered directly from the website.
Shipping in 4 - 8 weeks Shipping in 4 - 8 weeks
Packaging
TDS, SDS & Technical documents

Technical Specifications

General Properties
Color
Color
The color
 Yellow
Film Thickness 0.5 - 5 mm
Specific Gravity
Specific Gravity
Specific gravity (SG) is the ratio of the density of a substance to the density of a reference substance; equivalently, it is the ratio of the mass of a substance to the mass of a reference substance for the same given volume.

For liquids, the reference substance is almost always water (1), while for gases, it is air (1.18) at room temperature. Specific gravity is unitless.
 3.1
Mechanical Properties
Hardness
Hardness
Hardness is a dimensionless quantity. There is no direct relationship between measurements in one scale and their equivalent in another scale or another hardness test.
Durometer (Shore 00) 40
Electrical Properties
Dielectric Constant
Dielectric Constant
Dielectric Constant (k), commonly known as relative permittivity, is a number relating the ability of a material to carry alternating current to the ability of vacuum to carry alternating current.

It determines the ability of an insulator to store electrical energy and is the ratio of electric permeability in vacuum against the electric permeability of a material.

The lower the dielectric constant (κ) and dissipation factor, the less energy is absorbed from an electric field, making it a much better insulator.

It is a dimensionless property that can be affected by various factors such as the
thickness uniformity of a material, insufficient contact between the sample and electrodes, water adsorption and contact resistance.
Dielectric Constant @ 1000 kHz 6.6
Volume Resistivity
Volume Resistivity
Volume resistivity, also called volume resistance, bulk resistance or bulk resistivity is a thickness dependent measurement of the resistivity of a material perpendicular to the plane of the surface.
 4.8x1013 Ohms⋅cm
Thermal Properties
UL94 Rating
Flammability V-0
Thermal Conductivity
Thermal Conductivity
Thermal conductivity describes the ability of a material to conduct heat. It is required by power packages in order to dissipate heat and maintain stable electrical performance.

Thermal conductivity units are [W/(m K)] in the SI system and [Btu/(hr ft °F)] in the Imperial system.
 3.0 W/m.K
Thermal Impedance 0.65 °C·cm²/W

Additional Information

alt

Comrpession - Deflection @ Different Thickness of TGP300

 

Thickness range:

  • 0.5-5.0mm with 0.25mm incremental

 

Thickness Tolerance: >1mm, ±10%

  • 0.5-1mm, ±0.1mm
  • <0.5mm, ±0.05mm